Piles are basically load bearing building elements that are used to primarily transmit structural loads through the soil. Piles are majorly used to provide support to buildings located in areas that have poor soils. It basically consists of piles which can be made of timber, steel or concrete. The piles are then driven deep in to the ground till they reach the bedrock. This is worth knowing about marine pile drivers.
A bedrock is a hard surface located deep in the ground. At this level the piles cannot go any further hence providing stability to elements above. They exist in two major types which are the end bearing piles and friction piles. Friction piles are used when the load transmitted to the soil through skin friction between the surface of the pile and the soil.
When load is transmitted by the lower tip then end bearing piles are used. Supporting strength of most piles depend on combined effort of end bearing and friction. They are categorized depending on their use and the materials they are made of. Choosing good piles to use is quite crucial which means that the selection must be done with due care.
Choosing the type of piles to use is the duty of the contracted engineer. This means that the engineer must pick piles which are best suited to particular job. While doing this they must also figure in factors affecting performance and installation. Many consideration factors affect the selection decision. Weight of the structure to be supported and size are examples of factors to be considered.
Structures vary from a residential, commercial building, a simple structure like water tanks. What matters is the physical property of the soil. The presence of material for piles and the quantity of piles needed so as to have the structure supported. It is also vital to examine the depth required for piles to be laid so as to support the structure.
This is helpful in determining the type of pile driver to be used. Pile drivers are basically devices used to drive piles underground. Determining the type of load driver requires several investigations to be undertaken. Such investigations include site studies, geotechnical study and a basic penetration test should be done. Another very important test is the load test this is done to be able to establish the total amount of load to be carried by the pile.
When piles are driven underground the force that is used to support then is the same force that causes resistance to piles as they are being driven underground. In order to deal with this this is where the drivers come in. They help furnish the energy required to drive the piles underground.
These include pile hammers which are the most commonly used to drive piles underground. The hammers include the diesel hammers, which impart compression and explosion energy to the pile. Another type includes the vibratory hammers which utilize exciting shafts rotating in opposite direction to drive piles underground.
A bedrock is a hard surface located deep in the ground. At this level the piles cannot go any further hence providing stability to elements above. They exist in two major types which are the end bearing piles and friction piles. Friction piles are used when the load transmitted to the soil through skin friction between the surface of the pile and the soil.
When load is transmitted by the lower tip then end bearing piles are used. Supporting strength of most piles depend on combined effort of end bearing and friction. They are categorized depending on their use and the materials they are made of. Choosing good piles to use is quite crucial which means that the selection must be done with due care.
Choosing the type of piles to use is the duty of the contracted engineer. This means that the engineer must pick piles which are best suited to particular job. While doing this they must also figure in factors affecting performance and installation. Many consideration factors affect the selection decision. Weight of the structure to be supported and size are examples of factors to be considered.
Structures vary from a residential, commercial building, a simple structure like water tanks. What matters is the physical property of the soil. The presence of material for piles and the quantity of piles needed so as to have the structure supported. It is also vital to examine the depth required for piles to be laid so as to support the structure.
This is helpful in determining the type of pile driver to be used. Pile drivers are basically devices used to drive piles underground. Determining the type of load driver requires several investigations to be undertaken. Such investigations include site studies, geotechnical study and a basic penetration test should be done. Another very important test is the load test this is done to be able to establish the total amount of load to be carried by the pile.
When piles are driven underground the force that is used to support then is the same force that causes resistance to piles as they are being driven underground. In order to deal with this this is where the drivers come in. They help furnish the energy required to drive the piles underground.
These include pile hammers which are the most commonly used to drive piles underground. The hammers include the diesel hammers, which impart compression and explosion energy to the pile. Another type includes the vibratory hammers which utilize exciting shafts rotating in opposite direction to drive piles underground.
About the Author:
Get fantastic pile driver purchase tips, today. You can also get more information about state-of-the-art marine pile drivers at http://www.piledriver.org right now.
No comments:
Post a Comment